Influence of Spark Plasma Sintering Temperature on the Densification, Microstructure and Mechanical Properties of Al-4.5 wt.%Cu Alloy

doi:10.1007/s40195-013-0159-z

Abstract

Abstract:

The effect of sintering temperature on the densification mechanisms, microstructural evolution and mechanical properties of spark plasma sintered (SPS) compacts of a gas atomized Al-4.5 wt.%Cu alloy was investigated. The powder particles whose size varied between 10 to 500 μm was subjected to SPS at 400, 450 and 500℃ at a pressure of 30 MPa. The compact sintered at 500℃ exhibited fully dense microstructure which was characterized by a uniform distribution of the secondary phase, free of dendrites and micro-porosity. Microscopy and the SPS data reveal that the events such as particle rearrangement, localized deformation and bulk deformation appear to be the sequence of sintering mechanisms depending on the size range of powder particles used for consolidation. The compact sintered at 500℃ exhibited the highest hardness and compression strength since the microstructure was characterized by fine distribution of precipitates, large fraction of sub-micron grains and complete metallurgical bonding.

null

Key words: Spark plasma sintering, Sintering mechanisms, Precipitation, Compression strength

S. Devaraj, S. Sankaran, R.Kumar. Influence of Spark Plasma Sintering Temperature on the Densification, Microstructure and Mechanical Properties of Al-4.5 wt.%Cu Alloy[J]. Acta Metallurgica Sinica (English Letters), DOI: 10.1007/s40195-013-0159-z.

References

[1]J.M. Silcock, T.J. Heal and H.K. Hardy, J. Inst. Met.82(1954) 239.
[2]A. Guinier, Solid State Phys.9(1959) 293.
[3]U.H. Glaser, G. Dlubek and R. Krause, Phys. Status.Solidi B.163(1991) 337.
[4]Y. Nagai, M. Murayama, Z. Tang, T. Nonaka, K. Hono and M. Hasegava, Acta. Mater.49(2001) 913.
[5]S.C. Wang and M.J. Starink, Int. Mater. Rev.50 (2005) 193.
[6]H.D. Brody and M.C. Flemings, Trans. Met. Soc, AIME.236(1966) 615.
[7]T.Z. Kattamis, J.C. Coughlin and M.C. Flemings, Trans.Met. Soc. AIME.236(1967) 1504.
[8]T.Z. Kattamis, Y.V. Mirty and J.A. Reffner, J. Crystal Growth.19(1973) 237.
[9] G. Baumeister, B. Okolo and J. R?gner, Microsyst. Technol.14(2008) 1647.
[10] A.R.E. Singer, Met. Mater.4(1970) 246.
[11] S.M. Lee, J.H Jung, E. Fleury, W.T. Kim and D.H. Kim,Mater. Sci. Eng. A.294-296(2000) 99.
[12] M. Tokita, J. Soc. Powder Technol. Jpn.30(1993)790.
[13] J.K. Rana, Development of Bulk Nanocrystalline High Strength AA6061 Aluminum Alloy by High Energy Ball Milling, M.Technol Thesis, Indian Institute of Technology Madras, 2008.
[14] J.R. Groza and A. Zavaliangos, Mater. Sci. Eng. A.287(2000) 171.
[15] R. Chaim, Mater. Sci. Eng. A.443(2007) 25.
[16] J.R. Ryu, K.I. Moon and K.S. Lee, J. Alloys Compd. 296(2000) 157.
[17] Y. Murakoshi, T. Sano, I. Diewwanit, Y. Nakayama and S. Miyamoto, Proceedings of the 1st International Symposium on Spark Plasma Sintering (ISSPS-1), Singapore, September 06-08, 2001.
[18] O. Ohashi, G. Xie and K. Chiba, Spark Plasma Sintering of Pure Aluminum Powder and Bonding Behavior Powder Particles. Proceedings of the 1st International Symposium on Spark Plasma Sintering (ISSPS-1), Singapore, September 06-08, 2001.
[19] Y. Shiomi, J. Yoshino and N. Kuroishi, SPS Sintered Pre-Forms for High Strain Rate Super Plastic Forming. Proceedings of the 1st International Symposium on Spark Plasma Sintering (ISSPS-1),Singapore, September 06-08, 2001.
[20] G. Xie, O. Ohashi and N. Yamaguchi, Trans. Mater. Res.Soc. Jpn.27(2002) 743.
[21] T. Nagae, M. Yokota, M. Nose, S. Tomida, K. Otera, T.Kamiya and S. Saji, Mater. Trans.43(2002) 537.
[22] E. Fleury, J.H. Lee, S. H. Kim, G.S. Song, J.S. Kim, W.T.Kim and D.H. Kim, Mater. Res. Soc. Symp.643(2001) K2-1-1.
[23] Th. Schubert, J. Schmidt, T. Weissgarber and B.Kieback, World Powder Metallurgy Congress and Exhibition, PM-2010,Florence, Italy, October 10-14, 2010.
[24] S.W. Wang, L.D. Chen, Y.S. Kang, M. Niino and T. Hirai,Mater. Res. Bull.35(2000) 619.
[25] M. Tokita, J. Soc. Powder. Technol. Jpn.(1993)790.
[26] M. Ishiyama, Y. Bando and K. Kosuge, Proceedings of 1993 Powder Metallurgy World Congress, Japan Society of Powder and Powder metallurgy, Japan, 1993, p.931.
[27]J.M. Frei, U.A. Tamburini and Z.A. Munir, J. Appl. Phys.101(2007) 114914.
[28]C. Padmavathi, A. Upadhyaya and D. Agarawal, Mater. Chem.Phys.130(2011) 440.
[29]D.M. Albert, A. Anders, D.V. Dudina, J. Andersson, D.Jiang, C. Unuvar, U.A. Tamburini, E.J. Lavernia and A.K. Mukherjee,J. Appl. Phys.104(2008) 033305.
[30]S. Diouf and A. Molinari, Powder Technol.221 (2012) 220.
[31]R. Mehrabian, Int. Met. Rev.27(1982) 185.
[32]R. Willnecker, D.M. Herlach and B. Feuerbacher, Appl.Phys. Lett.49(1986) 1339.
[33]J.H. Perepezko, Mater. Sci. Eng.65(1984) 125.
[34]A.K. Srivastava, S.N. Ojha and S. Ranganathan, Metall.Mater. Trans. A29(1998) 2205.
[35]M. Gupta, F. Mohamed and E.J. Lavernia, Metall. Trans.A 23(1992) 831.
[36]Y. Abe, K. Miyasawa and M. Nakamura, Mater. Sci. Eng.98(1998) 351.
[37]R. Trivedi, F. Jin and I.E. Anderson, Acta Mater. 51(2003) 289.