AlN Precipitates and Microstructure in Non-oriented Electrical Steels Produced by Twin-roll Casting Process

doi:10.1007/s40195-012-0221-2

Abstract

Abstract:

Aluminum nitride (AlN) precipitates and microstructure of 4 wt.% (Si+Al) non-oriented electrical steel were investigated. The 2.0 mm thick cast strips with three different silicon/aluminum (Si/Al) ratios were produced by twin-roll casting process, then the strips were reheated, warm rolled, cold rolled and annealed. The microstructure and AlN precipitates were characterized using optical microscopy, scanning electron microscopy and transmission electron microscopy. The results showed that with the increase of Si/Al ratio, on the one hand, the casting microstructure changed from columnar grains to equiaxed grains, and the uniformity of annealed microstructure was improved; On the other hand, the number of AlN precipitates in cast strips reduced meanwhile the distribution became dispersed. By the reheat treatment, the size and distribution of the AlN precipitates can be changed. Moreover, the grain size of the annealed strips is in the range of 20-50μm, at the same time, many AlN precipitates were located at grain boundaries. Therefore, controlling the Si/Al ratio is a simple method to obtain desired microstructure. Then AlN precipitates in non-oriented electrical steel prepared by twin-roll casting process hinder markedly the recrystallized grains growth. A compatible reheat treatment can be an approach worth exploring to control the behavior of AlN precipitates.

Key words: Twin-roll casting, Non-oriented electrical steels, Microstructure, Aluminum nitride

Ting ZHANG, Xiaoming ZHANG, Zhiyuan GUO, Yuqian WANG,Chenggang LI, Liangyun LAN. AlN Precipitates and Microstructure in Non-oriented Electrical Steels Produced by Twin-roll Casting Process[J]. Acta Metallurgica Sinica (English Letters), 2013, 26(4): 483-488.

[1]	L. B. Tong, J. H. Chu, D. N. Zou, Q. Sun, S. Kamado, H. G. Brokmeier, M. Y. Zheng. Simultaneously Enhanced Mechanical Properties and Damping Capacities of ZK60 Mg Alloys Processed by Multi-Directional Forging [J]. Acta Metallurgica Sinica (English Letters), 2021, 34(2): 265-277.
[2]	Chun-Hua Ma, Fu-Sheng Pan, Ding-Fei Zhang, Ai-Tao Tang, Zhi-Wen Lu. Effects of Sb Addition on Microstructural Evolution and Mechanical Properties of Mg-9Al-5Sn Alloy [J]. Acta Metallurgica Sinica (English Letters), 2021, 34(2): 278-288.
[3]	Meichen Liang, Hao Zhang, Lifeng Zhang, Peng Xue, Dingrui Ni, Weizhen Wang, Zongyi Ma, Hengqiang Ye, Zhiqing Yang. Evolution of Quasicrystals and Long-Period Stacking Ordered Structures During Severe Plastic Deformation and Mixing of Dissimilar Mg Alloys Upon Friction Stir Welding [J]. Acta Metallurgica Sinica (English Letters), 2021, 34(1): 12-24.
[4]	Jinglin Liu, Qi Song, Lihui Song, Shude Ji, Mingshen Li, Zhen Jia, Kang Yang. A Novel Friction Stir Spot Riveting of Al/Cu Dissimilar Materials [J]. Acta Metallurgica Sinica (English Letters), 2021, 34(1): 135-144.
[5]	Xudong Du, Feng Wang, Zhi Wang, Xingxing Li, Zheng Liu, Pingli Mao. Hot Tearing Susceptibility of AXJ530 Alloy Under Low-Frequency Alternating Magnetic Field [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(9): 1259-1270.
[6]	Chao-Yue Zhao, Xian-Hua Chen, Peng Peng, Teng Tu, Andrej Atrens, Fu-Sheng Pan. Microstructures and Mechanical Properties of Mg-xAl-1Sn-0.3Mn (x = 1, 3, 5) Alloy Sheets [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(9): 1217-1225.
[7]	Dan-Yang Liu, Jin-Feng Li, Yong-Cheng Lin, Peng-Cheng Ma, Yong-Lai Chen, Xu-Hu Zhang, Rui-Feng Zhang. Cu/Li Ratio on the Microstructure Evolution and Corrosion Behaviors of Al-xCu-yLi-Mg Alloys [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(9): 1201-1216.
[8]	Yuan Yu, Peiying Shi, Kai Feng, Jiongjie Liu, Jun Cheng, Zhuhui Qiao, Jun Yang, Jinshan Li, Weimin Liu. Effects of Ti and Cu on the Microstructure Evolution of AlCoCrFeNi High-Entropy Alloy During Heat Treatment [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(8): 1077-1090.
[9]	Hui Jiang, Tian-Dang Huang, Chao Su, Hong-Bin Zhang, Kai-Ming Han, Sheng-Xue Qin. Microstructure and Mechanical Behavior of CrFeNi₂V_0.5W_x (x = 0, 0.25) High-Entropy Alloys [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(8): 1117-1123.
[10]	Ibrahim Ondicho, Bernard Alunda, Dicken Owino, Luke Otieno, Melody Chepkoech. Revealing a Transformation-Induced Plasticity (TRIP) Phenomenon in a Medium-Entropy Alloy [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(8): 1159-1165.
[11]	Qiuxin Nie, Hui Liang, Dongxu Qiao, Zhaoxin Qi, Zhiqiang Cao. Microstructures and Mechanical Properties of Multi-component Al_xCrFe₂Ni₂Mo_0.2 High-Entropy Alloys [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(8): 1135-1144.
[12]	Ren Li, Jing Ren, Guo-Jia Zhang, Jun-Yang He, Yi-Ping Lu, Tong-Min Wang, Ting-Ju Li. Novel (CoFe₂NiV_0.5Mo_0.2)_100-_xNb_x Eutectic High-Entropy Alloys with Excellent Combination of Mechanical and Corrosion Properties [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(8): 1046-1056.
[13]	Chengbo Yang, Jing Zhang, Meng Li, Xuejian Liu. Soft-Magnetic High-Entropy AlCoFeMnNi Alloys with Dual-Phase Microstructures Induced by Annealing [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(8): 1124-1134.
[14]	Ning Li, Cun-Lei Jia, Zhi-Wei Wang, Li-Hui Wu, Ding-Rui Ni, Zheng-Kun Li, Hua-Meng Fu, Peng Xue, Bo-Lv Xiao, Zong-Yi Ma, Yi Shao, Yun-Long Chang. Achieving a High-Strength CoCrFeNiCu High-Entropy Alloy with an Ultrafine-Grained Structure via Friction Stir Processing [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(7): 947-956.
[15]	Zhigang Zhang, Xiaotong Lu, Jianrong Xu, Hongjie Luo. Characterization and Tribological Properties of Graphene/Copper Composites Fabricated by Electroless Plating and Powder Metallurgy [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(7): 903-912.

AlN Precipitates and Microstructure in Non-oriented Electrical Steels Produced by Twin-roll Casting Process

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments