Creep crack growth in a Cr-Mo-V type steel: experimental observation and prediction

doi:10.11890/1006-7191-112-81

Abstract

Abstract: In this study, the creep crack growth (CCG) properties and fracture mechanism of a Cr-Mo-V steel at 566℃ in compact tension (CT) specimens were investigated, and the CCG rate was predicted by using the NSW model. The results show that the CCG rate measured by CT specimens is much lower than that predicted by the NSW model under plane-strain state. This means that the NSW model prediction for the CCG rate of the steel is over-conservative. In addition, the CCG rate da/dt versus C* measured by the experiments shows the piecewise linear relation on log-log scale instead of a single linear relation predicted by the NSW model. The main reasons for these results are that the actual creep fracture mechanism of the steel and the actual creep crack tip stress field in the CT specimens have not been fully captured in the NSW model. The experimental observation shows that the creep crack propagates in a discontinuous way (step by step) at meso-scale, and the cracks at micro-scale are usually formed by the growth and coalescence of voids on grain boundaries. The NSW model based on the creep ductility exhaustion approach may not correctly describe this creep fracture process. In addition, the opening stress and triaxial stress ahead of crack tips calculated by three-dimensional finite element method is lower than those predicted by the HRR stress field which is used in the NSW model under plane-strain state. The use of the high HRR stress field will cause high CCG rates. The change in the creep fracture mechanism at micro-scale in different ranges of C* may cause the piecewise linear relation between the da/dt and C* . Therefore, it is necessary to study the actual CCG mechanism in a wide range of C* and the actual creep crack tip stress field to establish accurate CCG prediction models.

Key words: Creep crack growth, Prediction, NSW model, Fracture mechanism, Finite element method

Jianping TAN, Guozhen WANG, Fuzhen XUAN and Shan-Tung TU. Creep crack growth in a Cr-Mo-V type steel: experimental observation and prediction[J]. Acta Metallurgica Sinica (English Letters), 2011, 24(2): 81-91.

References

[1] M. Yatomi, K.M. Nikbin and N.P. O'Dowd, Int J Pressure Vessels Piping 80 (2003) 573.

[2] D.W. Dean and D.N. Gladwin, Int J Pressure Vessels Piping 84 (2007) 378.

[3] P.J. Budden and D.W. Dean, Proc 8th Int Conf Creep and Fatigue at Elevated Temperatures (San Antonio, Texas, 2007).

[4] C.M. Davies, N.P. O'Dowd, K.M. Nikbin and G.A. Webster, Int J Solids Struct 44 (2007) 1823.

[5] K.M. Nikbin, D.J. Smith and G.A. Webster, Proc R Soc Lond A396 (1984) 183.

[6] K.M. Nikbin, D.J. Smith and G.A. Webster, J Eng Mater Technol 186 (1986) 186.

[7] G.A. Webster and R.A. Ainsworth, High Temperature Component Life Assessment (Chapman and Hall, London 1994).

[8] J.R. Rice and G.F. Rosengren, J Mech Phys Solids 16 (1968) 1.

[9] J.W. Hutchinson, J Mech Phys Solids 16 (1968)13.

[10] A.C.F. Cocks and M.F. Ashby, Metal Sci 14 (1980) 395.

[11] K.M. Nikbin, Mater Sci Eng A365 (2004) 107.

[12] M. Yatomi, N.P. O'Dowd, K.M. Nikbin and G.A. Webster, Eng Fract Mech 73 (2006) 1158.

[13] M. Tan, N.J.C. Celard, K.M. Nikbin and G.A. Webster, Int J Pressure Vessels Piping 78 (2001) 737.

[14] ASTM E 1457-00: Standard Test Method for Measurement of Creep Crack Growth Rates in Metals, Annual book of ASTM standards

[15] ABAQUS version 6.7, Hibbitt, Karlsson & Sorensen Inc (2007).

[16] B. Pan, Master Degree Thesis (East China University of Science and Technology, China, 2010).

[17] G.Z. Wang, X.L. Liu, F.Z. Xuan and S.T. Tu, Int J Solids Struct 47 (2010) 51.

[18] Z.D. Wang, PhD Dissertation (East China University of Science and Technology, China, 1990).

[19] X.L. Liu, Master Degree Thesis (East China University of Science and Technology, China, 2009).

[20] H. Ben Hadj Hamouda, L. Laiarinandrasana and R. Piques, Int J Pressure Vessels Piping 86 (2009) 228.

[21] M.Tabuchi, J. Ha, H. Hongo, T. Watanabe and T. Yokobori, Metall Mater Trans A35 (2004) 1757.

[22] D.R. Hayhurst, P.R. Brown and C.J. Morrison, Proc R Soc Lond A311 (1984) 131.