Rapid Ultrasonic-Assisted Soldering of AZ31B Mg Alloy/6061 Al Alloy with Low-Melting-Point Sn-xZn Solders Without Flux in Air

doi:10.1007/s40195-018-0749-x

Acta Metallurgica Sinica (English Letters) ›› 2019, Vol. 32 ›› Issue (3): 332-342.DOI: 10.1007/s40195-018-0749-x

收稿日期:2018-02-08 修回日期:2018-03-16 出版日期:2019-03-10 发布日期:2019-02-22
作者简介:

Huan Liu is a Lecturer, Master’s Supervisor, College of Mechanics and Materials, Hohai University. He earned his Ph.D. from Southeast University in 2014 and then became a Lecturer in Hohai University. He was selected into the “Shuangchuang Program of Jiangsu Province” and “Dayu Scholars Program of Hohai University” in 2017. So far, he has published more than 30 scientific papers (indexed by SCI) and held 2 authorized Chinese patents. His papers were cited more than 200 times. His research interests mainly include design of high-strength and high ductility magnesium alloys, heat-resistant magnesium alloys, fabrication of fine-grained and ultra-fine-grained metallic materials, and biomedical materials.

Xian-Hua Chen is a Professor of Chongqing University and received his Doctor’s degree from Institute of Metal Research, Chinese Academy of Sciences in 2008. He is Director of Institute of Functional Mg Alloys in National Engineering Research Centre for Magnesium Alloys, Director of International Joint Laboratory for Light Alloys (Ministry of Education), Editorial Board of Acta Metallurgica Sinica (English Letters) (SCI). His research work is focused on new high-performance structural and functional magnesium alloys, and purification technology of magnesium alloys. He also worked in Materials Technology Laboratory of CANMET in Canada as visiting scientist during 2012-2013. He has 22 patents, 1 book and more than 60 SCI papers, including 2 science papers. His papers were cited more than 2700 times. He was awarded the Provincial and Ministerial S&T Prize in 2013, 2014 and 2017. He was the Chairman of “The 2nd China Youth Scholars Conference on Mg Alloys.”

Rapid Ultrasonic-Assisted Soldering of AZ31B Mg Alloy/6061 Al Alloy with Low-Melting-Point Sn-xZn Solders Without Flux in Air

Zhi-Wei Lai^1,^2,³, Zhe-Yuan Huang^2,⁶, Chuan Pan³, Hui-Qiao Du⁴, Xiao-Guang Chen², Lei Liu², Wei-Ming Long⁵, Gui-Sheng Zou²()

1 School of Materials Science and Engineering, Tsinghua University, Beijing 100084, China
2 Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China
3 China Iron & Steel Research Institute Group, Beijing 100081, China;
4 Beijing Spacecraft Manufacturing Factory, Beijing 100190, China
5 The State Key Laboratory of Advanced Brazing Filler Metals and Technology, Zhengzhou Research Institute of Mechanical Engineering, Zhengzhou 450001, China
6 College of Materials Science and Engineering, Shanxi Key Laboratory of Advanced Magnesium-Based Materials, Taiyuan University of Technology, Taiyuan 030024, China

Received:2018-02-08 Revised:2018-03-16 Online:2019-03-10 Published:2019-02-22

摘要/Abstract

Abstract:

A novel ultrasonic-assisted low-temperature soldering was developed to join AZ31B Mg alloy and 6061 Al alloy with a series of Sn-xZn solders. The average maximum shear strength of the joints reaches up to 87.5 MPa at soldering temperature of 300 °C under ultrasonic assistance for only 5 s using Sn-20Zn solder. The fracture path propagates completely in the soldering seam. The results indicate that the microjet generated by ultrasonic pressure in liquid solder could strike and splinter the Mg₂Sn intermetallic compounds into small pieces, which contributes to the enhancement of the joint strength. In addition, the primary Al(Zn) solid solution phase formed during cooling stage could also strengthen the joint due to the prevention of microcracks propagation.

Key words: Ultrasonic-assisted soldering, Ultrasonic effect mechanism, Microjet, Intermetallic compound distribution, Solid solution, Joint strengthening

. [J]. Acta Metallurgica Sinica (English Letters), 2019, 32(3): 332-342.

Zhi-Wei Lai, Zhe-Yuan Huang, Chuan Pan, Hui-Qiao Du, Xiao-Guang Chen, Lei Liu, Wei-Ming Long, Gui-Sheng Zou. Rapid Ultrasonic-Assisted Soldering of AZ31B Mg Alloy/6061 Al Alloy with Low-Melting-Point Sn-xZn Solders Without Flux in Air[J]. Acta Metallurgica Sinica (English Letters), 2019, 32(3): 332-342.

图/表 14

Table 1 Chemical compositions of AZ31B Mg alloy and 6061 Al alloy (wt%)

Base metal	Al	Si	Zn	Mn	Mg
AZ31	2.5-3.5	0.1	0.5-1.5	0.2-0.5	Bal.
6061	98	0.5	0.0005	0.0038	0.97

Fig. 1 Schematic diagrams of ultrasonic-assisted soldering process a and shear strength test b

Fig. 2 Schematic diagrams of technological process parameters for different Zn contents of Sn-xZn (x = 0, 9, 20, 30, wt%) solders a and varied ultrasonic assistance time using Sn-20Zn solder b

Fig. 3 Microstructures of joint with different Zn contents: a pure Sn (260 °C); b Sn-9Zn (230 °C); c Sn-20Zn (300 °C); d Sn-30Zn (340 °C)

Fig. 4 Shear strength of Mg/Al alloy joint with a series of Sn-xZn solders

Fig. 5 Microstructures of joints with Sn-20Zn interlayer soldering under different ultrasonic assistance time: a 1 s; b 3 s; c 5 s; d 10 s; e 15 s

Fig. 6 Diagrams of acoustic cavitation effect: a formation process of acoustic bubble; b compression process of acoustic bubble; c distortion process of acoustic bubble; d collapse process of acoustic bubble

Fig. 7 Magnified microstructures of joints at Mg a-c and Al d-f alloys side interface with ultrasonic assistance time of 1 s a, d, 5 s b, e and 15 s c, f

Table 2 EDS results taken from possible phases (at.%)

Possible phase	Mg	Al	Sn	Zn
Sn	4.0	4.2	88.9	2.9
η-Zn	1.09	1.91	3.43	93.57
Mg₂Sn	66.9	1.7	27.9	3.5
Al(Zn) precipitated phase	0.8	87.9	00.4	10.6
Al(Zn) solid solution phase	0.88	92.23	1.2	6.22

Fig. 8 Joint fracture paths under varied ultrasonic assistance time: a 1 s; b 5 s; c 15 s

Fig. 9 Secondary electron a, c, e and backscattering electron b, d, f images of Sn-20Zn soldered joint fracture surface with ultrasonic assistance time of 1 s a, b, 5 s c, d; 15 s e, f

Fig. 10 a Joint shear strength and b XRD patterns of joint fracture surface with different ultrasonic assistance time

Fig. 11 Morphologies of Al(Zn) phase distribution a and microcrack propagation behavior b

Fig. 12 Joint formation model of ultrasonic-assisted soldering: a initial state of solders and base materials; b disintegration of layered Mg2Sn IMCs by microjet; c dispersive distribution of blocky Mg2Sn IMCs under ultrasound; d secondary crystallization of Mg2Sn IMCs

参考文献

[1]	W.S. Miller, L. Zhuang, J. Bottema, A.J. Wittebrood, P.D. Smet,A. Haszler, A. Vieregge, Mater. Sci. Eng. A 37, 280 (2000)
[2]	J. Liu, K. Zhao, M. Zhang, Y. Wang, L. An, Mater. Lett. 287,143(2015)
[3]	L. Liu, D. Ren, F. Liu, Materials 373, 67 (2014)
[4]	X.D. Qi, L.M. Liu, Mater. Des. 436, 33(2012)
[5]	A. Masoudian, A. Tahaei, A. Shakiba, F. Sharifianjazi, J.A. Mohandesi, Trans. Nonferrous Met. Soc. China 1317, 24 (2014)
[6]	G. Mahendran, V. Balasubramanian, T. Senthilvelan, Mater.Des. 1240, 30(2009)
[7]	S.S.S. Afghahi, M. Jafarian, M. Paidar, M. Jafarian, Trans.Nonferrous Met. Soc. China 1843, 26 (2016)
[8]	D.M. Fronczek, R. Chulist, L. Litynsk-Dobrzynska, S. Kac, N. Schell, Z. Kania, Z. Szulc, J. Wojewoda-Budka, Mater. Des.120, 130(2017)
[9]	Z.L. Liu, X.C. Meng, S.D. Ji, Z.W. Li, L. Wang, J. Manuf.Process. 552, 31(2018)
[10]	W.S. Liu, L.P. Long, Y.Z. Ma, L. Wu, J. Alloys Compd. 34, 643(2015)
[11]	Y. Wang, P.B. Prangnell, Mater. Charact. 84, 134(2017)
[12]	L.M. Liu, J.H. Tan, X.J. Liu, Mater. Lett. 2373, 61(2007)
[13]	L.M. Liu, J.H. Tan, L.M. Zhao, X.J. Liu, Mater. Charact. 479, 59(2008)
[14]	Z.W. Xu, L. Ma, J.C. Yan, S.Q. Yang, S.Y. Du, Compos. Part A407, 43 (2012)
[15]	Z. Wang, H. Wang, L. Liu, Mater. Des. 14, 39(2012)
[16]	C.T. Kwok, C.H. Man, F.T. Cheng, Mater. Sci. Eng. A 108, 242(1998)
[17]	X.G. Chen, J.C. Yan, F. Gao, J. Wei, Ultrasonics Sonochem.144, 20(2013)
[18]	Z.W. Xu, J.C. Yan, G. Wu, X. Kong, S. Yang, Scr. Mater. 835,53(2005)
[19]	Y. Xiao, H.J. Ji, M.Y. Li, J.Y. Kim, H.B. Kim, Mater. Des. 717,47(2013)
[20]	Y. Zhang, J.C. Yan, X.G. Chen, Y. Cui, Trans. Nonferrous Met.Soc. China 726, 20 (2010)
[21]	R.S. Xie, X.G. Chen, Z.W. Lai, L. Liu, G.S. Zou, J.C. Yan, W.X. Wang, Mater. Des. 19, 91(2016)
[22]	Z.Y. Huang, H.Q. Du, L. Liu, Z.W. Lai, X.G. Chen, W.M. Long,W.X. Wang, G.S. Zou, Ultrason. Sonochem. 101, 43(2018)
[23]	Z. Lai, C. Pan, H. Du, X.G. Chen, R.S. Xie, L. Liu, W.M. Long,G.S. Zou, Sci. Technol. Weld. Join. 19, 23(2018)
[24]	W. Guo, T. Luan, J. He, J.C. Yan, Mater. Des. 85, 125(2017)
[25]	X.Y. Yu, W.Q. Xing, M. Ding, Ultrason. Sonochem. 216, 31(2016)
[26]	W. Guo, T.M. Luan, J.S. He, J.C. Yan, Ultrason. Sonochem.815, 40(2018)
[27]	ASM International Handbook Committee, Properties andSelection: Irons, Steels, and High-Performance Alloys, 10th edn.(ASM International, Materials Park Campus, 1990)
[28]	Y. Li, X. Leng, S. Cheng, J. Yan, Mater. Des. 427, 40(2012)
[29]	K.S. Suslick, D.A. Hammerton, R.E. Cline, J. Am. Chem. Soc.5641, 108(1986)
[30]	X.G. Chen, R.S. Xie, Z.W. Lai, L. Liu, J.C. Yan, G.S. Zou, J.Mater. Sci. Technol. 492, 33(2017)
[31]	E.A. Brujan, P.R. Williams, Chem. Eng. Res. Des. 293, 84(2006)
[32]	Z. Zhang, H.M. Urbassek, Comput. Mater. Sci. 109, 145(2018)

Rapid Ultrasonic-Assisted Soldering of AZ31B Mg Alloy/6061 Al Alloy with Low-Melting-Point Sn-xZn Solders Without Flux in Air

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

图/表 14

参考文献

相关文章 0

编辑推荐

Metrics

本文评价