Optimization of Mechanical and Wear Properties of Functionally Graded Al6061/SiC Nanocomposites Produced by Friction Stir Processing (FSP)

doi:10.1007/s40195-015-0235-7

金属学报英文版 ›› 2015, Vol. 28 ›› Issue (5): 584-590.DOI: 10.1007/s40195-015-0235-7

所属专题： Friction Stir Welding In AMSE 2015-2017

收稿日期:2014-07-07 修回日期:2014-11-24 出版日期:2015-03-19 发布日期:2015-07-23

Optimization of Mechanical and Wear Properties of Functionally Graded Al6061/SiC Nanocomposites Produced by Friction Stir Processing (FSP)

M. Saadatmand, J. Aghazadeh Mohandesi()

Department of Mining and Metallurgical Engineering, Amir Kabir University of Technology, Hafez Ave, Tehran, Iran

Received:2014-07-07 Revised:2014-11-24 Online:2015-03-19 Published:2015-07-23

摘要/Abstract

Abstract:

The objective of present work is to apply the friction stir processing (FSP) to fabricate functionally graded SiC particulate reinforced Al6061 composite and investigate the effect of SiC particle mass fraction distribution on the mechanical properties and wear behavior of Al6061/SiC composite. Regarding the obtained results in this work, with increasing SiC mass fraction, elongation decreased, but hardness enhanced. However, the optimized functionally graded composite with the highest tensile strength and wear resistance was achieved for composite with 10 wt% surface SiC. Also, the results showed that wear resistance and tensile strength decreased for composite with 13 wt% surface SiC, due to reinforcement particle clustering depending on high SiC mass fraction.

Key words: Functionally graded composite, Wear, Mechanical properties, Friction stir processing (FSP)

. [J]. 金属学报英文版, 2015, 28(5): 584-590.

M. Saadatmand, J. Aghazadeh Mohandesi. Optimization of Mechanical and Wear Properties of Functionally Graded Al6061/SiC Nanocomposites Produced by Friction Stir Processing (FSP)[J]. Acta Metallurgica Sinica (English Letters), 2015, 28(5): 584-590.

图/表 13

Fig. 1 a Dimension (unit: mm) of the used pin for FSP; b appearance of FSPed Al6061 with SiC particles

Fig. 2 a Photograph of the composite zone for F10 composite; b Illustration of the position of tensile specimen

Fig. 3 Schematic illustration of wear test

Fig. 4 Fraction of SiC as a function of distance from surface of FG composites

Fig. 5 Microhardness as a function of distance from surface of FG composites

Fig. 6 Optical macroscopic appearances of cross section of F2 a, F5 b, F8 c, F10 d, F13 e samples

Fig. 7 Back-scattered SEM images of F2 a, F5 b, F8 c, F10 d, F13 e samples, arrows A in Fig. 7e showing clustering for F13

Fig. 8 Stress-strain curves of F2, F5, F8, F10, and F13 samples

Table 1 Mechanical properties and weight loss of F2, F5, F8, F10, and F13 samples

Composite	0.2% yield strength (MPa)	Ultimate strength (MPa)	Weight loss (g)
F₂	102	185.3	0.0092 ± 0.0002
F₅	117	205.3	0.0060 ± 0.0002
F₈	144	234.5	0.0041 ± 0.0002
F₁₀	176	248	0.0025 ± 0.0002
F₁₃	152	198.3	0.0032 ± 0.0002

Fig. 9 SEM micrograph of worn surfaces of F2 a, F5 b samples

Fig. 10 SEM image of worn surface of F8 sample

Fig. 11 SEM image of worn surface of F10 sample

Fig. 12 SEM image of worn surface of F13 sample

参考文献 34.

1.	I. Charit, R.S. Mishra,Acta Mater. 53, 4211(2005)
2.	C. Lee, J.C. Huang, P. Hsieh,Scr. Mater. 54, 1415(2006)
3.	D.K. Lim, T. Shibayanagi, A.P. Gerlich,Mater. Sci. Eng. A 507, 194(2009)
4.	Y. Moruisad, H. Fujii, T. Nagaoka, K. Nogi, M. Fukusumi,Composites A 38, 2097 (2007)
5.	A. Shafiei-Zarghani, S.F. Kashani-Bozorg, A. Zarei-Hanzaki,Mater. Sci. Eng. A 500, 84(2009)
6.	R.S. Mishra, M.W. Mahoney, S.X. McFadden, N.A. Mara, A.K. Mukherjee,Scr. Mater. 42, 163(2000)
7.	J.R. Gomes, L.A. Rocha, S.J. Crnkovic, R.F. Silva, A.S. Miranda, Mater. Sci. Forum 423-425, 91 (2003)
8.	D.S. Zhou, F. Qiu, H.Y. Wang, Q.C. Jiang,Acta Metall. Sin.(Engl. Lett.) 27, 798(2014)
9.	C.S. Ramesh, A.R.A. Khan, N. Ravikumar, P. Savanprabhu,Wear 259, 602(2005)
10.	J. Hu, D.Y. Li, R. Llewellyn,Wear 259, 6(2005)
11.	J.K.M. Kwok, S.C. Lim,Compos. Sci. Technol. 59, 55(1999)
12.	M. Saadatmand, J.A. Mohandesi,J. Mater. Eng. Perform. 23, 736(2014)
13.	M. Salehi, M. Saadatmand, J.A. Mohandesi,Trans. Nonferrous Met. Soc. China 22, 1055(2012)
14.	R. Sathiskumar, N. Murugan, I. Dinaharan, S.J. Vijay,Mater. Charact. 84, 16(2013)
15.	M. Salehi, H. Farnoush, J.A. Mohandesi,Mater. Des. 63, 419(2014)
16.	P. Asadi, M.K. Besharati,Givi. Int. J. Adv. Manuf. Technol. 51, 247(2010)
17.	L.L.M. Jr,Mishnaevsky. Compos. Sci. Technol. 66, 1873(2006)
18.	S. Amada, S. Untao,Composites B 32, 451(2001)
19.	G.B. Veeresh Kumar, C.S.P. Rao, N. Selvaraj,Composites B 43, 1185(2012)
20.	H.L. Lee, W.H. Lu, S.L. Chan,Wear 159, 223(1992)
21.	H. Pouraliakbar, R. Bagheri, S.M. SeyedReihani,Ceram. Int. 40, 8809(2014)
22.	A. Mazahery, H. Abdizadeh, H.R. Baharvandi,Mater. Sci. Eng. A 518, 61(2009)
23.	S.A. Sajjadi, M. Torabi Parizi, H.R. Ezatpour, A. Sedghi,J. Alloys Compd. 511, 226(2011)
24.	E.A. Diler, R. Ipek,Mater. Sci. Eng. A 548, 43(2012)
25.	S. Kumar, V. Balasubramanian,Wear 264, 1026(2008)
26.	S. Suresha, B.K. Sridhara,Compos. Sci. Technol. 70, 1652(2010)
27.	M. Walczak, D. Pieniak, M. Zwierzchowski,Arch. Civ. Mech. Eng. 15, 116(2015)
28.	R.L. Deuis, C. Subramanian, J.M. Yellup,Compos. Sci. Technol. 57, 415(1997)
29.	Y.Z. Zhan, G.D. Zhang, Y.H. Zhuang,Mater. Trans. 45, 2332(2004)
30.	E.R.I. Mahmoud, M. Takahashi, T. Shibayanagi, K. Ikeuchi,Wear 268, 1111(2010)
31.	A. Vencl, I. Bobic, B. Stojanovic,Ind. Lubr. Tribol. 66, 66(2014)
32.	A. Wang, H.J. Rack,Acta Metall. Mater. 40, 2301(1992)
33.	Y.C. Lin, H.C. Li, S.S. Liou, M.T. Shie,Mater. Sci. Eng. A 373, 363(2004)
34.	P.N. Bindumadhavan, T.K. Chia, M. Chandrasekaran, H.K. Wah, L.N. Lam, O. Prabhakar,Mater. Sci. Eng. A 315, 217(2001)

Optimization of Mechanical and Wear Properties of Functionally Graded Al6061/SiC Nanocomposites Produced by Friction Stir Processing (FSP)

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

图/表 13

参考文献 34.

相关文章 0

编辑推荐

Metrics

本文评价